Destiny's Call
Aegis (4+), and the wearer’s model’s Arm is set to always 3.
Note that this means it cannot be improved beyond 3. It is still affected by AP.
Aegis (4+), and the wearer’s model’s Arm is set to always 3.
Note that this means it cannot be improved beyond 3. It is still affected by AP.
The wearer gains +1 Armour and Aegis (3+, against Flaming Attacks). The wearer automatically fails all Fortitude Saves.
Attached and Resistance (Melee Attacks).
The wearer gains +1 Health Point and Fortitude (5+).
Successful to-hit rolls with Close Combat Attacks against the wearer must be rerolled.
During Spell Selection, randomise a Magic Path (from all Paths in this book). The bearer is a Wizard Apprentice using the randomised Path. It cannot select the Hereditary Spell. The bearer cannot take any Special Items nor any other upgrades that are restricted to Wizards (or any types of Wizards).
The bearer gains Aegis (5+).
The bearer gains the Hereditary Spell during Spell Selection, always knows it in addition to its other spells, cannot select it during Spell Selection, andcannot replace or otherwise lose it.
The bearer gains Channel (1).
One use only. May be activated when the bearer’s model fails an Armour Save. This failed Armour Save may be rerolled.
The bearer’s unit must reroll natural to-hit rolls of ‘1’
The bearer gains Stand Behind and cannot issue Duels.
One use only. May be activated after Siphon the Veil (at the end of step 3 of the Magic Phase Sequence).
When activated, pick an enemy model and select one of its Attribute, Bound, or Learned Spells. The selected model cannot cast the chosen instance of the spell during this Magic Phase. Only a single Binding Scroll may be activated during the same phase.
One use only. May be activated at the start of any Round of Combat. Until the end of the Player Turn, the bearer gains +3 Agility.
Breath Attack (Str 4, AP 1, Flaming Attacks, Stand and Shoot).
Fortitude (5+).
The wielder gains +X Attack Value while using this weapon, and attacks made with this weapon gain +X Strength, +X Armour Penetration, and Magical Attacks, where X is equal to the number of enemy Characters in base contact with the wielder’s unit. This bonus is calculated at the Initiative Step when the attacks are made.
Attacks made with this weapon gain +1 Strength, +1 Armour Penetration, and become Magical Attacks.
Strength modifiers from this weapon (combining both mundane and Weapon Enchantment modifiers) cannot exceed +2 (but can exceed +2 through modifiers from other sources, such as spells).
At the start of each Round of Combat, the wielder may choose to have attacks made with this weapon become Flaming Attacks and Magical Attacks.
Crush Attack. This Crush Attack always hits on 4+.
Attacks made with this weapon gain +1 Armour Penetration. In addition, attacks with a natural to-hit roll of ‘6’ made with this weapon become Divine Attacks and gain Multiple Wounds (D3).
While using this weapon, the wielder gains Grind Attacks (D3) that are resolved with Toxic Attacks at Initiative Step 10.
+3 Arm. The Armour Value can never be improved beyond 5.
The range of the model’s Commanding Presence is increased to 18″.
When determining the Secondary Objective, randomize two objectives instead of one, and choose which of the two objectives to play.
Whenever you draw a Flux Card, apply the effects from the list below based on the number of the Flux Card. Effects have Duration: One Turn.
Card Number Effects applied to all models on the Battlefield
1, 5, 9, 13 Sulfurous Gas: All Terrain Features gain Dangerous Terrain.
2, 6, 10, 14 Ash Cloud: −1 to hit with Shooting Attacks.
3, 7, 11, 15 Obsidian Deposits: −1 to Casting Rolls.
4, 8, 12, 16 Ominous Rumbling: −1 Cou.
One use only. You may activate this ability when Choosing Equipment and Abilities. Set the model part’s Att to 4, Str to 5, and AP to 3. The model part gains Fortitude (4+). The model cannot use any weapons while this ability is active. Duration: One Turn.
An army with an Innovative Leader may use different Base Sizes than those
listed in the Unit Entries. Any Unit Entry using this option must have the new
base size noted on the Army List, and all models in the unit must have the same
Base Size. The new bases must:
• Be between 100% – 125% of the original width.
• Be between 100% – 150% of the original depth.
• Both width and depth must be divisible by 5 mm.